# Instar 2905 v1 hängt in Reboot-Schleife, tot! **URL:** https://forum.instar.com/t/instar-2905-v1-haengt-in-reboot-schleife-tot/22689 **Category:** IN-2905 **Created:** [29. Dezember 2014 um 17:38 UTC](https://forum.instar.com/t/instar-2905-v1-haengt-in-reboot-schleife-tot/22689 "2014-12-29T17:38:32Z") **Posts on this page:** 4 **Page:** 1
### Author: ![AHERR2](https://forum.instar.com/letter_avatar_proxy/v4/letter/a/ad7895/32.png) [@AHERR2](https://forum.instar.com/u/AHERR2) #### Post date: [29. Dezember 2014 um 17:38 UTC](https://forum.instar.com/t/instar-2905-v1-haengt-in-reboot-schleife-tot/22689/1 "2014-12-29T17:38:32Z")
Hallo, meine Instar-2905v1-Kamera hängt in einer Reboot-Scheife und läuft nicht mehr an. Das „Wiederherstellen der Kamera nach einem fehlerhaften Firmware Update“ habe ich auch durchgeführt, aber daran lag es nicht. Ist sonst irgendetwas defekt? SerienNr: 201103278 Die Kamera müsste eine v1 sein, ich habe auch dafür die Daten aufgespielt. Hier das Logfile: > W90P745 Boot Loader [Version 1.1 $Revision: 1 $] Rebuilt on May 11 2010 Memory Size is 0x1000000 Bytes, Flash Size is 0x400000 Bytes Board designed by Winbond Hardware support provided at Winbond Copyright (c) Winbond Limited 2001 - 2006. All rights reserved. Boot Loader Configuration: ``` MAC Address : 00:EA:21:63:68:F2 IP Address : 0.0.0.0 DHCP Client : Enabled CACHE : Enabled BL buffer base : 0x00300000 BL buffer size : 0x00100000 Baud Rate : -1 USB Interface : Disabled Serial Number : 0xFFFFFFFF ``` For help on the available commands type ‚h‘ Press ESC to enter debug mode … Cache enabled! Processing image 1 … Processing image 2 … Processing image 3 … Processing image 4 … Processing image 5 … Processing image 6 … Processing image 7 … Unzip image 7 … Executing image 7 … Linux version 2.4.20-uc0 (root@maverick-linux) (gcc version 3.0) #1013 Èý 12ÔÂ 2 13:17:32 CST 2009 Processor: Winbond W90N745 revision 1 Architecture: W90N745 On node 0 totalpages: 4096 zone(0): 0 pages. zone(1): 4096 pages. zone(2): 0 pages. Kernel command line: root=/dev/rom0 rw Calibrating delay loop… 39.83 BogoMIPS Memory: 16MB = 16MB total Memory: 14376KB available (1435K code, 288K data, 40K init) Dentry cache hash table entries: 2048 (order: 2, 16384 bytes) Inode cache hash table entries: 1024 (order: 1, 8192 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 4096 (order: 2, 16384 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Winbond W90N745 Serial driver version 1.0 (2005-08-15) with no serial options enabled ttyS00 at 0xfff80000 (irq = 9) is a W90N745 Winbond W90N7451 Serial driver version 1.0 (2005-08-15) with no serial options enabled ttyS00 at 0xfff80100 (irq = 10) is a W90N7451 I2C Bus Driver has been installed successfully. Blkmem copyright 1998,1999 D. Jeff Dionne Blkmem copyright 1998 Kenneth Albanowski Blkmem 1 disk images: 0: 7F0E0000-7F16BFFF [VIRTUAL 7F0E0000-7F16BFFF] (RO) S29GL032N Flash Detected 01 eth0 initial ok! which:0 PPP generic driver version 2.4.2 Linux video capture interface: v1.00 Winbond Audio Driver v1.0 Initialization successfully. usb.c: registered new driver hub add a static ohci host controller device : USB OHCI at membase 0xfff05000, IRQ 15 hc\_alloc\_ohci usb-ohci.c: AMD756 erratum 4 workaround hc\_reset usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb.c: registered new driver audio audio.c: v1.0.0:USB Audio Class driver usb.c: registered new driver serial usbserial.c: USB Serial Driver core v1.4 * * * |\_\_ / _| \_ \ / \ / **| / / | | | | | |/ \_ \ \_** / /| || | |_| / \_\_\_ \ _**) | / ** __\__ , |_** // \_\_**_/ |\_\_\_/ ZD1211B - version 2.24.0.0 usb.c: registered new driver zd1211b main\_usb.c: VIA Networking Wireless LAN USB Driver 1.13 usb.c: registered new driver vntwusb usb.c: registered new driver rt73 dvm usb cam driver 0.0.0.0 by Maverick Gao in 2006-8-12 usb.c: registered new driver dvm dvm usb cam driver 0.1 for sonix288 by Maverick Gao in 2009-4-20 usb.c: registered new driver dvm usb cam driver for sonix288 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 1024 bind 2048) VFS: Mounted root (romfs filesystem) readonly. Freeing init memory: 40K BINFMT\_FLAT: bad magic/rev (0x74202d74, need 0x4) BINFMT\_FLAT: bad magic/rev (0x74202d74, need 0x4) Shell invoked to run file: /bin/init Command: mount -t proc none /proc Command: mount -t ramfs none /usr Command: mount -t ramfs none /swap Command: mount -t ramfs none /var/run Command: mount -t ramfs none /etc Command: mount -t ramfs none /flash Command: mount -t ramfs none /home Command: camera& [8] Command: sh Sash command shell (version 1.1.1) /\> hub.c: connect-debounce failed, port 1 disabled new USB device :80fd7e04-fed640 hub.c: new USB device 1, assigned address 2 p1[7]:1,j 3,config-\>bNumInterfaces:4 usbaudio: device 2 audiocontrol interface 2 has 1 input and 0 output AudioStreaming interfaces usbaudio: valid input sample rate 16000 usbaudio: device 2 interface 3 altsetting 1: format 0x00000010 sratelo 16000 sratehi 16000 attributes 0x01 usbaudio: valid input sample rate 48000 usbaudio: device 2 interface 3 altsetting 2: format 0x00000010 sratelo 48000 sratehi 48000 attributes 0x01 usbaudio: registered dsp 14,35 usbaudio: warning: found 1 of 0 logical channels. usbaudio: assuming the channel found is the master channel (got a Philips camera?). Should be fine. usbaudio: registered mixer 14,32 usb\_audio\_parsecontrol: usb\_audio\_state at 00ff35a0 new USB device :80fb3004-fed640 hub.c: new USB device 2, assigned address 3 VIA Networking Wireless LAN USB Driver Ver. 1.13 Copyright (c) 2004 VIA Networking Technologies, Inc. aw version is 0.25.2.6 aw version is 29.5.3.13 Wait for auto-negotiation complete…ResetPhyChip Failed MAC Line-on… Wait for auto-negotiation complete…open video device error MAC Line-off… myreboot ---
### Author: ![muck](https://forum.instar.com/user_avatar/forum.instar.com/muck/32/3_2.png) [@muck](https://forum.instar.com/u/muck) #### Post date: [29. Dezember 2014 um 21:43 UTC](https://forum.instar.com/t/instar-2905-v1-haengt-in-reboot-schleife-tot/22689/2 "2014-12-29T21:43:53Z")
> [@AHERR2;14398](#): > > Hier das Logfile: Wo hast du das log-file her, bzw wie hast du das aufgerufen? Gruss Michael ---
### Author: ![AHERR2](https://forum.instar.com/letter_avatar_proxy/v4/letter/a/ad7895/32.png) [@AHERR2](https://forum.instar.com/u/AHERR2) #### Post date: [29. Dezember 2014 um 22:17 UTC](https://forum.instar.com/t/instar-2905-v1-haengt-in-reboot-schleife-tot/22689/3 "2014-12-29T22:17:13Z")
Hallo, ich habe die Kamera geöffnet und mich mit einem „USB to serial UART Interface“ an die serielle Schnittstelle gehängt. [http://www.instar.de/faq\_restore\_firmware](http://www.instar.de/faq_restore_firmware) Gruss AHERR2 ---
### Author: ![muck](https://forum.instar.com/user_avatar/forum.instar.com/muck/32/3_2.png) [@muck](https://forum.instar.com/u/muck) #### Post date: [29. Dezember 2014 um 22:24 UTC](https://forum.instar.com/t/instar-2905-v1-haengt-in-reboot-schleife-tot/22689/4 "2014-12-29T22:24:42Z")
Ich glaube kaum, dass dir hier ein user zielführende Hilfe geben kann. Das wäre eine Sache für den INSTAR-Support. Der ist aber erst ab dem 6.1.15 wieder erreichbar. Gruss Michael